You can, but it is extremely complicated and not worth it. If you have a stock stereo and you have the remote wire there you want to in twine the remote wire with the power wire before inserting in the power slot for amp. That's why we went with the standard system.
This could be caused by a bad ground. Can you put a sound system into a stock radio? That is because a standard head unit on your radio plays a very wide range of sounds. Read on to learn all you need to know on hooking subs up to stock radio. Last thing you need is a dead battery.
How to Hook Up a Subwoofer System to a Car s Stock Stereo
- You want to ground your cap.
- The way to avoid distortion is by using an amplifier for your subs.
- Can you hook a ipod up to a car radio?
- The motor that raises and lowers the antenna is controlled by a wire which is connected to the power switch in the stock radio.
- Did you cut factory plug for radio hook up?
Where do I hook up the orange wire when installing an aftermarket radio in a dodge Dakota? The fuse amperage should match the gauge size. You could add additional subs to your system using these outputs.
Can you Hook Subs to a Stock Stereo? How do you hook up a amp to a stock radio in a jeep Grnd Cherokee? Your much better off just getting the deck with the dash mount and wiring harness so it makes hook-up easier and allows you to swith back to stock incase you decide to sell the vehicle later on. The amp is wired to the head unit and then the subs are wired to the amp.
It does not have such cable at all. Clipping is the number one reason of bass distortion. This converter can then be connected directly to your amplifier's line level inputs. Just match the positive and negatives. Free Shipping on All Orders!
How do you connect subwoofers without all the wires? The sub cuts on and off at high volume when I use the auxiliary cord to phone. And if so, would you have to run wires from the door speakers to the sub location, and then another set of wires back to the doors to the speakers? Run the power wire to your amp.
June edited March in Car Subwoofer Talk. My amp is already installed and I just bought a new sub. How do you hook up a cb radio in truck? So, now that you know you need to wire an amp to the radio and then the subs to the amp you may be wondering how do you do that.
Adding subwoofer to stock car radio
To submit your questions or ideas, or to simply learn more about It Still Works, contact us. Run your amp wires battery, ground. Subs and amps should be matched as closely as possible for best performance and longevity.
Well, it is time for reassembly, dating but sometimes this can be hard. How do I connect my new sub to my old amp? Your amp could be installed near the speaker in the trunk or under a seat.
There should be a black ground wire in the Chevy Celebrity radio wiring harness. Choose a subwoofer speaker system and amplifier that fits your car's current system and meets your audio needs. Turn the gain all the way down, start playing music and turn it up to where you usually listen, where the mids sound good.
How to hook up subs and amp to stock stereo in car
- How do you unlock Malibu radio?
- Where do you hook a ground wire up for a car radio?
- Mounting brackets and speaker enclosures can be purchased at any local car audio retailer.
- You also need to run power from the radio to the amp and then from the amp to the sub.
The key with this is to get a good amp to match with your good subs and also use good speaker wire. Touch the wires that were connected to the stock radio to a hot wire and see if the antenna starts to move. Will the wires still match up on the aftermarket radio I purchased?
Can You Hook Subs To A Stock Stereo
Include your email address to get a message when this question is answered. Figure out where you're going to place the amp, put the beginning of your power red wire there and give it about a foot of wire extra, then begin to hide and run the power wire to under the hood. You can also mount the amp into the trunk, but some amps have controls that you might want to reach easier. After you have that you have to take wires and connect them to the output of the amplifier. This article was written by the It Still Works team, copy edited and fact checked through a multi-point auditing system, in efforts to ensure our readers only receive the best information.
Lightly sand the contact area to expose clean metal before attaching ground. This will come into play later. Then you have to find the output wires for the sound range that you need and connect them to the input of the amplifier. Run yourself a good wire for ground directly to the chassis.
Cookies make wikiHow better. Tips If your amp doesn't turn on, check the amp fuses. Once you got everything wired you may be wondering what to do next. Instead, you should wire an amp to the stock sound system and then wire the subs to the amp. It will just plug into your truck and then connect color coordinated wires.
Buy a new radio and install it. It is actually a good way to get a sound boost from your radio without having to give up the familiar controls. Check the manuals included with your line-out converter, stereo and amplifier for complete installation instructions for your system. Run the power wire through the firewall.
Your rear speakers are on the rear deck, so its easy to tag on to your speaker wires there. Brought to you by Techwalla. If you want to get involved, best pick up lines click one of these buttons!